Bergeon 30081-P05 Set of 5 Screwdrivers| |
Set consists of 5 Bergeon 30081 stainless steel series screwdrivers (sizes: 0.80, 1.00, 1.20, 1.40, 1.60 mm).
| |
BERG-30081-P05
$61.80
|
Bergeon 30081-TAM Drum Barrel 1.20 Millimeter Screwdriver| |
The large drum barrel allows for more torque while screwing/unscrewing tight screws.
| |
BERG-30081-TAM-120
$18.90
|
Bergeon 30081-TAM Drum Barrel 1.40 Millimeter Screwdriver| |
The large drum barrel allows for more torque while screwing/unscrewing tight screws.
| |
BERG-30081-TAM-140
$18.90
|
Bergeon 30081-TAM Drum Barrel 1.60 Millimeter Screwdriver| |
The large drum barrel allows for more torque while screwing/unscrewing tight screws.
| |
BERG-30081-TAM-160
$18.90
|
Bergeon 5659-2.50 Jumbo Stainless Steel Screwdriver w/ Special Knurled Handle 2.50 mm| | Bergeon Swiss Made Stainless Steel 2.50 mm Screwdriver with special knurled handle and ball bearing head. The big 18 mm diameter domed head design makes it easier to rest your palm on top and 8 mm diameter special knurled handle helps your fingers grip the body better, while the ball bearing inside the top of the head spins with ease as you unscrew tough and stubborn screws. Uses the stainless steel screwdriver blade 6899-M-250.
| |
BERG-5659-2.50
$48.95
Special $45.00
|
Bergeon 5659-3.00 Jumbo Stainless Steel Screwdriver w/ Special Knurled Handle 3.00 mm| | Bergeon Swiss Made Stainless Steel 3.00 mm Screwdriver with special knurled handle and ball bearing head. The big 18 mm diameter domed head design makes it easier to rest your palm on top and 8 mm diameter special knurled handle helps your fingers grip the body better, while the ball bearing inside the top of the head spins with ease as you unscrew tough and stubborn screws. Uses the stainless steel screwdriver blade 6899-M-300.
| |
BERG-5659-3.00
$48.95
Special $45.00
|
$926.00
Bergeon 5700-Z Case Opener| | The Bergeon 5700 is one of the finest watch case openers made. Supplied with four pairs of non-marring case holding plugs (for 13 to 22 millimeter lug spread), 6 sets of bits, and a bit holder that opens up to a maximum diameter of 60 MM. This opener will open most waterproof cases with no additional accessories. There are, however, a variety of optional accessories to open most other watches, including suction openers (FB-222 and FB-223) for cases that the supplied bits do not fit, and Rolex watches (FB-231 and FB-230). I recommend the lower rubber cup set (FB-223) for best protection of the watch with all kinds of bits and other upper devices. The 5700 holds the watch case very firmly in a level position, much reducing chance of slippage and scratching. Alignment and control is perfect. If you want a very well-made, versatile, professional-quality case opener, this is the one to get. A single gouged back on an expensive watch will cost you more than the price of this wrench. | |
FB-220
$926.00
|
Bergeon 5808-V Green Bench Mat| | Bergeon bench mat, standard green does not reflex light. Structured, stiff and isopropyl alcohol resistant surface with a self-adhesive back. 320 x 240 x 1.5 mm (12 5/8" x 9 7/16" x 1/16") | |
BERG-5808-V
$54.00
|
Bergeon 6620 Strap-Notching Tool| |
This Bergeon tool is the Rolls Royce of watch-strap notching tools. The complete set contains Wooden Stand, Pliers with 1 rotating 6 slotted die head, 3 half-round punches, #6620-G 2 mm x 5.8 mm, #6620-H 4 mm x 5.8 mm, #6620-J 6 mm x 8.50 mm, and 3 rectangular punches #6620-D 2 mm x 5 mm, #6620-E 4 mm x 5 mm, #6620-F 6 mm x 7.5 mm. Used for cutting shapes into leather straps, not for hole punching. An ideal tool for the demanding professional. In aluminium casting. Fine quality. Length 160 mm. With adjustable strap guide.
| |
FB-511
$496.00
|
Bergeon 7853 Fine Woven White Microfiber Cloth| | Cloth made of 80% polyester and 20% polyamide. Ideal presentation and cleaning cloth while handling watches and jewelry items, removes oils and fingerprints from display items and will not leave behind lint fibers. Dimensions: 300 x 300 mm.
| |
BERG-7853
$5.95
|
Bergeon 7965 Series Screwdriver & Dynamometric Cylinder Set in Aluminum Case| |
Premium suitcase in aluminium set comes with 10 screwdrivers with special profile (Sizes: 0.50 mm, 0.60 mm, 0.80 mm, 1.00 mm, 1.20 mm, 1.40 mm, 1.60 mm, 2.00 mm, 2.50 mm and 3.00 mm), tube with 2 stainless steel replacement blades for each screwdriver size, tube with 1 HSS curvature blade for each screwdriver size and 10 dynamometric cylinders (10 nmn, 15 nmn, 20 nmn, 25 nmn, 30 nmn, 35 nmn, 40 nmn, 45 nmn, 50 nmn and 55 nmn).
Handle made of stainless steel with special profile compatible with the 7965-C series cylinder.
Tube with 2 conical blades made of hardened stainless steel 54HRC reference 6899-T.
Tube with 1 parallel blade reference 6895-M, per diameter.
Head made of synthetic material POM self-lubricant.
Can be used also without dynamometric cylinder.
Ø from 0.50 mm to 3.00 mm
10 exchangeable dynamometric cylinders
Stainless steel.
Compatible with all specific. screwdrivers reference 7965-…
Preset, fixed torque: from 10 to 55 mNm.
Bidirectional.
Can be positioned on the whole length of the screwdriver
Possibility to mount 2 cylinders, one for screw control, the other for unscrew control.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-PREMIUM
$3,100.00
|
Bergeon 7965-050 Special Knurled Handle 0.50 mm Screwdriver| |
This 0.50 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-050
$24.80
|
Bergeon 7965-060 Special Knurled Handle 0.60 mm Screwdriver| |
This 0.60 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-060
$24.80
|
Bergeon 7965-070 Special Knurled Handle 0.70 mm Screwdriver| |
This 0.70 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-070
$24.80
|
Bergeon 7965-080 Special Knurled Handle 0.80 mm Screwdriver| |
This 0.80 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-080
$24.80
|
Bergeon 7965-090 Special Knurled Handle 0.90 mm Screwdriver| |
This 0.90 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-090
$24.80
|
Bergeon 7965-100 Special Knurled Handle 1.00 mm Screwdriver| |
This 1.00 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-1.00
$24.80
|
Bergeon 7965-110 Special Knurled Handle 1.10 mm Screwdriver| |
This 1.10 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-110
$24.80
|
Bergeon 7965-1.20 Special Knurled Handle 1.20 mm Screwdriver| |
This 1.20 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-120
$24.80
|
Bergeon 7965-130 Special Knurled Handle 1.30 mm Screwdriver| |
This 1.30 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-130
$24.80
|
Bergeon 7965-140 Special Knurled Handle 1.40 mm Screwdriver| |
This 1.40 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-1.40
$24.80
|
Bergeon 7965-150 Special Knurled Handle 1.50 mm Screwdriver| |
This 1.50 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-150
$24.80
|
Bergeon 7965-160 Special Knurled Handle 1.60 mm Screwdriver| |
This 1.60 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-160
$24.80
|
Bergeon 7965-180 Special Knurled Handle 1.80 mm Screwdriver| |
This 1.80 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-180
$24.80
|
Bergeon 7965-200 Special Knurled Handle 2.00 mm Screwdriver| |
This 2.00 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-200
$24.80
|
Bergeon 7965-220 Special Knurled Handle 2.20 mm Screwdriver| |
This 2.20 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-220
$24.80
|
Bergeon 7965-250 Special Knurled Handle 2.50 mm Screwdriver| |
This 2.50 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-250
$24.80
|
Bergeon 7965-300 Special Knurled Handle 3.00 mm Screwdriver| |
This 3.00 mm screwdriver has a special knurled stainless steel handle, made to be used with the 7965-C demountable dynamometric cylinder (sold separately). The screwdriver can also be used without the 7965-C demountable dynamometric cylinder. The self lubricating head is made from polyoxymethylene (POM).
| |
BERG-7965-300
$24.80
|
Bergeon 7965-C10 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers (sold separately) for controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 10 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C10
$258.00
Special $228.00
|
Bergeon 7965-C15 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers (sold separately) for controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 15 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C15
$258.00
Special $228.00
|
Bergeon 7965-C20 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers (sold separately) for controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 20 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C20
$258.00
Special $228.00
|
Bergeon 7965-C25 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers (sold separately) for controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 25 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C25
$258.00
Special $228.00
|
Bergeon 7965-C30 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers (sold separately) for controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 30 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C30
$258.00
Special $228.00
|
Bergeon 7965-C35 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers (sold separately) for controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 35 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C35
$258.00
Special $228.00
|
Bergeon 7965-C40 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers for (sold separately) controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 40 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C40
$258.00
Special $228.00
|
Bergeon 7965-C45 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers (sold separately) for controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 45 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C45
$258.00
Special $228.00
|
Bergeon 7965-C50 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers (sold separately) for controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 50 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C50
$258.00
Special $228.00
|
Bergeon 7965-C55 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers (sold separately) for controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 55 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C55
$258.00
Special $228.00
|
Bergeon 7965-C60 Demountable Dynamometric Cylinder| | This stainless steel dynamometric cylinder mounts onto the 7965 screwdrivers (sold separately) for controlled torque when tightening and loosening screws. When the force that is generated exceeds the rated amount of the cylinder, the excess force will be dispersed by the cylinders rotation, therefore preventing over tightening the screw and snapping the screw head. 60 mNm.
2 cylinders can be mounted onto the same screwdriver to test if the screw has been tightened properly. A watchmaker would use the cylinder with the specified mNm force for the movement to tighten the screw, then use the cylinder with a slightly lower mNm force to check if the screw has been tightened completely. If the screw can be loosened with the lower mNm force, then the screw is not tightened properly.
Special order item. Please allow 4-6 weeks for delivery.
| |
BERG-7965-C60
$258.00
Special $228.00
|
Bergeon 7965-S10 Special Knurled Handle Screwdriver Set with Deluxe Heavyweight Stand
| |
Set comes with 10 stainless steel special knurled handle screwdrivers made to be used with or without the 7965-C demountable dynamometric cylinder (sold separately). The wider body allows a nice grip even when not using the 7965-C demountable dynamometric cylinder. The head is made of Polyoxymethylene (POM) synthetic material and is self-lubricating.
Sizes of screwdrivers are .50 mm, .60 mm, .80 mm, 1.00 mm, 1.20 mm, 1.40 mm, 1.60 mm, 2.00 mm, 2.50 mm, and 3.00 mm. Also comes with replacement stainless steel blades for all screwdrivers.
Special order item. Please allow 4-6 weeks for delivery
| |
BERG-7965-S10
$414.00
|
Bergeon 7965-T Removable Drum| | Designed to be used with the 7965 series screwdrivers (sold separately) for better control and increased force when tightening and loosening screws.
| |
BERG-7965-T
$36.95
|
Bergeon 7995 Balance Bridge Support "Balance Tack"| |
Enables the watchmaker to position the balance bridge with his balance-spring, while avoiding polluting the staff pivot with oil. Simply place the balance bridge screw hole through the brass spike and now you can easily make any corrections, inspections or repairs. Swiss made.
| |
BERG-7995
$27.85
|
Bergeon 8745 Multifunction Bracelet Press| |
Bergeon has re-designed the traditional bracelet press with the limited space that watchmakers have on their bench in mind. By using composite material for the body and adding a removable compartment for accessories at the base, this creates a light weight and space saving tool. The 8745 multifunction bracelet press can punch out and install pins, unscrew and screw on bracelet screws on watch bracelets.
Supplied with one slotted base number 6744-P, one pin holder with drum number 6745-PG-A, two bases with adjustable height number 8745-SRC and 6745-SR-28, one set of 6 blades number 6745-M (sizes: 2x .80, 2x 1.00, 2x 1.20) and 2 Phillips number 6745-MC (size: 1.50 and 2.00 mm), and one set of 6 pins number 6745-G (sizes: .40, .60, .80, 1.00, 1.50 & 2.0 mm).
The slotted base number 6744-P allows to maintain in a good position watches with leather or metal bracelet. Both bases number 8745-SRC and 6745-SR28 allow the height adjustment.
| |
BERG-8745
$206.00
|
Bergeon B-Net Cloth | | Large size cloth measuring at 330 x 330 mm, giving you more surface area to work with. Made of 70% polyester and 30% polyamide.
| |
BERG-2208
$16.80
Special $15.30
|
Bergeon Clear Protection Film Masking Sticker Roll 7164-050-T060| |
Protective Film with slight adhesive back. For packaging of watches, jewels or other luxury items. Clear Masking Stickers in a roll 50 mm wide by 50 meters long. Thickness is 0.06 mm.
| |
BERG-7164-050-T060
$43.80
|
Bergeon Clear Protection Film Masking Sticker Roll 7164-080-T060| |
Protective Film with slight adhesive back. For packaging of watches, jewels or other luxury items. Clear Masking Stickers in a roll 80 mm wide by 50 meters long. Thickness is 0.06 mm.
| |
BERG-7164-080-T060
$89.16
Special $79.95
|
Bergeon Latex Finger Cots Large, Sold by the Dozen| |
Latex cots for watchmaking, electronics or chemical work. 1 Dozen: $1.95, 1 Gross = 144pcs: $9.12, 10 Gross = 1440 pcs: $81.60.
| |
BERG-5840-L
$1.95
|
Bergeon Replacement Curvature Screwdriver Blades
Sizes: 0.50, 0.60, 0.70, 0.80, 1.00, 1.10, 1.20, 1.30, 1.40, 1.50, 1.60, 1.80, 2.00, 2.20, 2.50, 300 mm.
|
Bergeon Tool for Adjusting Eccentric Screw on ETA 7750
| |
Screwdriver with adapted blade to adjust the eccentric screw of the minute counter for the calibre range ETA Valjoux 7750. Also for Calibers 7751, 7753, 7754, 7757, 7758, 7760, 7765, 7768, 7770, A07.211 and A07.231
| |
BERG-31081-EX-7750
$37.44
|
Bergeon's 7812 Quick Battery and Bracelet Service Kit in Hard Case| |
This set is a Jewelers dream for watch battery replacing and for bracelet changing and sizing. Comes with 18 specialized tools and accessories in a hard plastic travel case. Everything you need to open cases, install batteries along with all you need to size, install and remove bracelets: Steel spring bar tool (6767-S), jaxa mini case wrench with square pins (2819-MINI), watchmakers pocket/case knife (7403), 4x eye loupe (2611-2.5), non-magnetic tweezer #00 (7026-00) 2 stainless screwdrivers and replacement blades 1.00mm and 1.60mm (30081-100, 30081-160, 6899-M-100, 6899-M-160), plastic battery tweezer with steel lip (6460-P), screw type bacelet pin remover (7230), flat nose plier (2510-N), microfiber cleaning cloth (7039), flexible bracelet gauge (6789) 1 spare fork tip for spring bar tool 6767-S (6767-A) , 1 spare pin tip for spring bar tool 6767-S (6767-B), 1 plastic tube (30080-TN). Click here to order the tools individually.
| |
BERG-7812
$316.00
|
Bergeon's 7815 Master Service Set in Hard Case| |
This master service set is truly a must have set for watch battery service, watch bracelet changes, length setting, opening and closing of screwed waterproof watch back covers. Comes with 46 specialized tools and accessories in a hard plastic travel case:
Full size Jaxa case wrench (Bergeon 2819-08), 4 sets of 3 bits for the Jaxa case wrench (Bergeon 2819-A, 2819-B, 2819-C, 2819-D), multifunction bracelet press (Bergeon 8745), bracelet holder block (Bergeon 6744-P), 4x loupe (Bergeon 2611-TN-2.5), plastic tweezers with steel lip (Bergeon 6460-P), anti-magnetic, stainless steel tweezers (Bergeon 7026-1), 5 stainless steel screwdrivers 1.00 mm, 1.20 mm, 1.40 mm, 1.60 mm and 2.00 mm (Bergeon 30081-100, 30081-120, 30081-140, 30081-160, 30081-200), 5 tubes with 2 spare screwdriver blades (Bergeon 6899-T Ø1.00 mm, 1.20 mm, 1.40 mm, 1.60 mm and 2.00 mm), snap back case knife (Bergeon 4932), flat nose pliers (Bergeon 2510-N), microfiber cloth (Bergeon 7039), flexible measuring band for wrists (Bergeon 6789-N), spring bar tool (Bergeon 3135), spare pin & fork ends for 3135 spring bar tool (Bergeon 3153-R), leather buff stick with buff protector (Bergeon 1282A & 4056-6), steel ruler (Bergeon 2819-08-R), 6 plastic boxes Ø15 x 30mm (Bergeon 2963-B), and dust blower (Bergeon 30540)
Click here to order the tools individually.
Special Order Item. Please allow 4-6 weeks for delivery.
| |
BERG-7815
$949.00
|
Individual Bergeon Ergonomic Screwdrivers
Click here for replacement screwdrivers for BERG-6899.
|
Moebius Lubricant Starter Kit for Mechanical Watches| | Starter oil kit designed especially for mechanical watches contains: 9010/2ml, 9104/5ml, 9415/2ml, 9504/5ml, 9501/5ml. Comes in a hard plastic case.
| |
MOEBIUS-8500-KIT-MEC
$189.95
|
Moebius Lubricant Starter Kit for Quartz Watches| | Starter oil kit designed especially for quartz watches contains: 9501-SC/5ml, 9104-SC/2ml, 8302/5ml, 9014/2ml, 8212-SC/5ml. Comes in a hard plastic case.
| |
MOEBIUS-8500-KIT-QUA
$149.95
|
New Bergeon Professional Hand Setter 8935| |
When having the best tools possible really count only this new hand setter from Bergeon will do. Set comes with 4 color coded bit holders and 4 color coded hand setting bits (Bit outer diameter/Hole diameter - 2.60mm/1.6mm, 2.10mm/1.20mm, 1.70mm/0.60mm, 1.50mm/No hole.) Movement holder is sold separately. Movement holders with a base diameter of 31mm will work on this hand setting tool. Click here for the Bergeon 1996 movement holder that will fit the 8935 hand setting tool.
Special order item, please allow 4-6 weeks for delivery. Credit Card are not billed for special order items until they are shipped.
| |
BERG-8935
$1298.00
|
Bergeon 30180-A Die Cast Alloy Four White Ceramic Cups Metal Oil Stand | | This is the finest oil cup stand on the market and is a must have item for any watchmaker. Only a little bit of oil should be placed in each of the agate cups at a time. Oil should be transferred to the cups by large drops from a large oiler or a clean nail. In the center of the stand is pith wood cup for cleaning the oilers. The white ceramic cup makes it easier to see the oil. Comes with 4 white ceramic 8 mm well cups. | |
BERG-30180-A-C2
$177.60
|
Bergeon 30081-TAM Drum Barrel 1.30 Millimeter Screwdriver| |
The large drum barrel allows for more torque while screwing/unscrewing tight screws.
| |
BERG-30081-TAM-130
$18.90
|
$154.00
Bergeon 30081-S09 Nine Piece Stainless-Steel Screwdriver Set with Rotating Stand| |
The Bergeon 30081-S features 9 Stainless Steel screwdrivers and spare blades. The color-coded swivel head makes it easier for size recognition. Comes on a nine slot rotating stand that keeps your screwdrivers organize.
Sizes of the screwdrivers are 0.50, 0.60, 0.80, 1.00, 1.20, 1.40, 1.60, 2.00 and 2.50mm. Includes 9 spare blades. Swiss made.
| |
BERG-30081-S09
$154.00
|
