Otto Frei.
Quality Jewelry Supplies for Generations - Since 1930
Contact UsHome Search for Products About Us

Milling Tools, Brubaker Taps, Validus Keyless Jacobs Chucks

   

Set of 3 Brubaker Plug Hand Screw Tap GH3, 1/4-28 NF, HSS

New old stock, Brubaker Screw Tap
High Speed Steel

BRUBAKER-1/4-28-NF
$18.95
order.gif  checkout.gif

  

Large Taps & Dies
Presto made in England Taps and Dies. SPHINX Taps made in Switzerland, TITEX High Speed Steel Taps made in Germany, Kestag made in Austria, HSS Dies from Italy!
   

Set of 3 Brubaker Plug Hand Screw Tap GH3, 12-24 NF, HSS

New old stock, Brubaker Screw Tap
High Speed Steel

BRUBAKER-12-24-NC
$18.95
order.gif  checkout.gif

    

Set of 3 Brubaker Plug Hand Screw Tap GH3, 5/16"-24 NF, HSS

New old stock, Brubaker Screw Tap
High Speed Steel

BRUBAKER-5/16-24-NF
$18.95
order.gif  checkout.gif
   

Set of 3 Brubaker Plug Hand Screw Tap GH3, 12-28 NF, HSS

New old stock, Brubaker Screw Tap
High Speed Steel

BRUBAKER-12-28-NF
$18.95
order.gif  checkout.gif

    

NEW VALIDUS KEYLESS JACOBS DRILL CHUCK 1/32"-1/2"

New old stock, found in our forgotten lathe and milling inventory. Made in Italy, by Validus size 0 - 13 MM. Fits a CM2 tampered mounting shank.

VALIDUS-0-13-KEYLESS
$96.00
order.gif  checkout.gif
   

Morse Taper Milling Arbor For Drill Chucks, Morse-Jacobs Size CM2

The AGP Taper Milling Arbor, made in Italy for Drill Chuck, entirely of hardened and ground steel. Size CM2 is made to fit the Validus Jacobs chuck 0-13 mm. Will also fit other Jacob chucks requiring a CM2 size taper arbor. Length End to End 4.26"

ARBOR-APL-CM2
$19.95
order.gif  checkout.gif

    

Threaded 3/8" Milling Arbor For Jacobs Chuck

The AGP Taper Milling Arbor, made in Italy for Drill Chuck, entirely of hardened and ground steel.

Fits the VALIDUS-0-06-KEYLESS Jacobs Chuck

ARBOR-MILL-THREAD3-8
$19.95
order.gif  checkout.gif
   

Diamond Core Drill 1 Inch Diameter

Some Neycraft Core Drilling Instructions:
A 1 inch diamond core drilling agate should be run at approximately 100 R.P.M. To start a hole, begin by kissing the stone with the drill until a clouding appears in the coolant. When this occurs, increase the pressure and continue drilling, Throughout the drilling cycle, oscillate the drill up and down rapidly. To minimize edge chipping when through hole drilling, back the stone with a glass plate.

DRILL-DIAMOND-CORE1
$86.00
order.gif  checkout.gif

    

LATHE-DISK

LATHE-DISK
$99.00
order.gif  checkout.gif
   

Taper Milling Arbor For Drill Chucks, Jacobs Size CM2

The AGP Taper Milling Arbor, made in Italy for Drill Chuck, entirely of hardened and ground steel.

ARBOR-APL-CM2
$19.95
order.gif  checkout.gif

    

Taper Milling Arbor For Drill Chucks, Jacobs Size CM2

The AGP Taper Milling Drill Chuck Arbor is a superior quality product, which was made in Italy, entirely of hardened and ground steel.

ARBOR-APL-CM2
$29.95
order.gif  checkout.gif
   

Jacobs Chuck 33-B16 With Key 32, 5/64-1/2" Made In Sheffield England

New, Unused Vintage Jacobs Chuck with capacity from 5/64" to 1/2" (2 to 13 mm).

JACOBS-CHUCK-33-B16
$52.95



    

Taper Milling Arbor Size 33x3 For Jacobs Drill Chuck

The AGP Taper Milling Arbor, made in Italy for Drill Chuck, entirely of hardened and ground steel.

Size 33x3 fits the Jacobs Chuck 33-B16, 5/64-1/2" Made In Sheffield England

ARBOR-MILL-33X3
$19.95
order.gif  checkout.gif
 

SPHINX SPIREC High Speed Micro Steel Drills Made In Switzerland
Special sale on SPHINX SPIREC High Speed Micro Drills
SPHINX Flat Micro Pivot Drills
SPHINX Straight Shank Micro Pivot Drills
SPHINX Micro Center Drills
While Supply Last
 

SPHINX SPIREC High Speed Steel Flat Micro Drills Made In Switzerland
Special sale on SPHINX SPIREC High Speed Steel Flat Micro Pivot Drills and Mascot HSS Flat Pivot Drills.

Flat Pivot Drills are made with a rake angle of zero degrees. They made be used wherever drilling is done without a drill bushing. In many cases these drill can be used without first making a center.

 

SPHINX SPIREC High Speed Steel Micro Center Drills Made In Switzerland
www.ofrei.com
Otto Frei, Watch Parts Since 1930
Customers Entrance
126 2nd St. Oakland, California 94607
Mailing Address: PO BOX 796, Oakland Ca. 94604
Freight Shipment Address: 119 3rd St. Oakland Ca. 94607 USA


Home   |  About Us   |  Specials   |  Contact Us   |  Search

Click here to send email

For stock checks on watch parts not listed on the site please call the watch material department at 510-832-0355 ext 3., Monday to Friday 9 AM to 5 PM Pacific Standard Time Zone.
Stock Checks For Watch Movement & Watch Case Parts

Security/Privacy/Return Policy

United States
 510.832.0355 EXT. 3
800.900.3734 (fax)

International
 510.832.0355 EXT. 3
510.834.6217 (fax)