Miscellaneous Watch Tools

Sometimes the case back does not screw off or snap off and the only way to gain entrance to the watch movement is thru the crystal. The watch would then have what is know as a two-piece stem and crown and after you removed the crown you just insert this pump into the hole and pump away until the plastic crystal pops off the case. To Remove crystals quickly and safely. Available with 3 heads: diameter at 1.60, 2.00, and 2.50mm. 1 key for removing the half-stem with the crown.

BERG-5011
$181.00
 

Collet-tightening and reaming tool. Five different notches for tightening all sizes of hairspring collets and for reaming.

BERG-3007
$169.00
 

Slip movement supplied with one .75 mm high-speed steel, oversized shank twist drill.

FB-718
$46.20
 

Bergeon set includes six double-ended cutters. Perfect to enlarging holes, clean screw heads, clear dial feet, and doing beveling.

FB-766
$337.68
 

Great for polishing pivots, pinions and much more. Five differnt shapes are available: Flat 3 mm, Flat 4 mm, 1/2 Round shape, Crossing and this Round Pointed. The useful length of the sapphire burnishing end is 25 mm long.

30401-3
$249.00
 

Great for polishing pivots, pinions and much more. Five differnt shapes are available: Flat 3 mm, Flat 4 mm, Round Pointed, Crossing and this 1/2 Round shape. The useful length of the sapphire burnishing end is 25 mm long.

30401-4
$310.00
 

Great for polishing pivots, pinions and much more. Five differnt shapes are available: Flat 4 mm, 1/2 Round shape, Round Pointed, Crossing and this Flat 3 mm. The useful length of the sapphire burnishing end is 25 mm long.

30401-6
$214.00
 

This useful Bergeon tool for removing broken screws in a plate or bridge. The broken shaft of the screw.The tool grips the broken shaff of the screw from above and below. Supplied with 2 reversible double ended 1.0 mm and 0.8 mm tips. Extra reversible double ended tips sizes 0.40 mm/0.50mm and 0.60 mm/0.70 mm tips are also available sold per piece.

FB-2832
$109.95
 

Priced per piece.

30209-A
$13.95
 

The FB-2832 Bergeon Screw Extractor is supplied with two of this size broaches.

30209-C
$13.95
 

Bergeon Crown Winder for Mechanical Watches number 30409D, for 2-4 mm crowns. Great for people who can no longer wind crowns without some discomfort.

FB-2879
$41.20
 

Bergeon Crown Winder for Mechanical Watches number 30409A, for 3-5 mm crowns. Great for people who can no longer wind crowns without some discomfort.

FB-2880
$41.20
 

Bergeon Crown Winder for Mechanical Watches number 30409C, for 4-6 mm crowns. Great for people who can no longer wind crowns without some discomfort.

FB-2881
$41.20
 

Bergeon Crown Winder for Mechanical Watches number 30409B, for 5-7 mm crowns. Great for people who can no longer wind crowns without some discomfort.

FB-2882
$41.20
 

Removes excess solder from the base of the dial feet , which keep the dial from fitting.

BERG-30512
$123.60
 

Replacement work-drivers for Bergeon 30090 driver opener. Assortment includes one of each size (small hole diameter x large hole diameter): 0.25 x 0.30, 0.32 x 0.35, 0.35 x 0.38, 0.40 x 0.45, 0.45 x 0.50, 0.55 x 0.60, 0.65 x 0.70, 0.70 x 0.75, 0.75 x 0.80, 0.85 x 0.90, 0.95 x 1.00, 1.05 x 1.10 mm.

BERG-30091-A
$114.00
 

This pliers-type cannon-pinion tightener is one quick way to increase friction on the center wheel pinion. With screw regulated opening system.

FB-713
$159.00
 

Used for adjusting fancy shape plastic crystals and sanding metals.

FB-956
$1.40
 

Bergeon Screw Tip Finisher with 3 lanterns and wooden handle. Use for rounding off and polishing screw ends. The 3 different lanterns are made to fit screw threads with diameter .40, .60, and .80 mm. The lanterns hold the screw thread tightly, so that it won't move around while you work on it. It is very difficult or even impossible to round off and polish screw ends without this tool; giving that the part is so tiny. Forget the hassle and get this tool.

BERG-2003
$82.44
 

Tool comes with 3 different lantern diameters used for rounding off and polishing screw ends. The 3 different lanterns are made to fit screw threads with diameter .40, .60, and .80 mm. The lanterns hold the screw thread tightly, so that it won't move around while you work on it. It is very difficult or even impossible to round off and polish screw ends without this tool; giving that the part is so tiny. Forget the hassle and get this tool.

MSA 03.010
$61.00
 

Screwdriver with blade to turn out ETACHRON Pitons. Fine adjustment of the spiral centering between the racket pins. Has small opening at the tip for adjusting the regulator pins. Overall length: 3.75 inches.

BERG-16918-TETC
$34.95
 

Screwdriver with blade to remove ETACHRON Pitons. Has small fork shaped tip for removing the stud block. Overall length: 3.75 inches.

BERG-16918-EETC
$39.95
 

Special tool for use on Incabloc's Novodiac spring in ETA 2801, 2824.2, 2834.2, and 2836.2 movements. Comes in a red aluminum handle and measures 94 mm from end to end. Swiss made.

MSA 03.011
$36.95
 

Special tool for use on Incabloc's Novodiac spring in ETA 2671, 2660, and 2688 movements. Comes in a red aluminum handle and measures 94 mm from end to end. Swiss made.

MSA 03.012
$34.95
 

Allows stable support of the balance complete without damaging the hairspring when cleaning the impulse pin.

BERG-7990
$19.40
 

Polystyrene stick with pointed end on one side and flat end on the other. Length is 135 mm with 4 mm diameter.

BERG-6436
$3.49
 

Bergeon Diamantine powder are of high quality and packaged in containers of 15 grams. Larger sizes are available upon request.

BERG-6807-EF
$9.65
 

Tool used to help measure the correct spot of where to cut, when shortening a stem.

BERG-2002
$149.16
 

A wonderful tool that sure looks good. Allows the pivots to be straightened without breaking due to a control device as well as a screw fitted with a stop. 41 Jewelled holes diam. 0.07 - 0.15 mm. Progression 0.025 mm. Bergeon reference #30350-D-02.

FB-743
$708.00
 

Simply apply & heat to fill cracks and chips on enamel dials. Before applying the dial enamel to the chipped and cracked areas you need to clean the dial as well as possible. Soap, water and a soft brush is an old time method. Others will now use an ultrasonic cleaner will a jewelry cleaning solution, which is different than watch cleaner used on the movement parts. After cleaning the dirt out of small cracks you might not notice them as much or at all. When the dial is fully cleaned, completely dried, oil and dust free you are now ready to apply the dial enamel material. Place a small amount over the crack or chipped area where you see the metal showing. You want to use just enough to fill the area when the enamel is melted. To heat the enamel over the low heat flame of an alcohol lamp until the enamel begins to warm, soon it will completely flow and fill the cracks and chipped places. You want to remove the dial from the heat before the enamel spreads to areas that you do not need or want it to flow. Excess dial enamel should then be removed and a new shape razor blade is recommended for the removal of excess material.

FB-120
$19.95
 

The expandable jaw automatically grips any size or shape of lock nut, hex nut, star nut, cap nut, or round nut. The Nut and Screw Grabber doubles as a screw starter! Placing a screw in the self-closing jaws makes it easy to thread even the smallest screw into the hardest to reach place. The more pressure you apply, the tighter the grip on the screw.

FB-13.450
$11.95
 

Great for polishing pivots, pinions and much more. The useful length of the sapphire burnishing end is 25 mm long.

30401-5
$330.00
 

Tool for closing efficiently watch barrel covers without leaving any marks. Diameter up to 21 mm.

MSA 03.310
$30.60
 

Every collector and repairer of Pocket Watch needs a set of keys for key wind watches. These 12 different sizes of keys at a low price will be useful to have available when needed for winding and setting.

PWK-100.14
$16.78